Axel nut

[dan3490]

any 1 know of a way to get the axle nut off a 92 teg? its on dirt and the tire keeps spinning theres no brake fluid or pads on it so i have no clue how else to get the tire to stop spinning so i can take the passenger side axle off

[Nick_S]

Use a strong impact wrench.

[nicklk]

"you can do it, put'cher back into"

[dan3490]

lmfaoooooo i can do it riiiight 156 lb or torque n i weigh 120 i tryed jumpin on the 4' break bar and the fucker just flew back and wacked me i the chest maybe ill just whip out the 12' bar and try lolol thats how we go my homies off but thats not my prob just tryin to get the damn tire to stop spining

[Dave_L]

Good luck. lol. Can you set the car back down on the ground? If you can, do that and put it in gear. That should work for ya.

[jackmode9316]

Ummm can you roll it to pavement at least?

[dan3490]

lmfaoooo its a shell and its on the ground on the dirt lol and yea i can put it on pavment if i want to push the shell out my backyard back over some stairs and the to then street no drive way or garage at my house pretty lame...also im doin all this work my self sucks

[nicklk]

What I've done in the past, is jam a breaker bar between two of the lugs without the rims on, so that the handle is pressed against the ground, then torque on the nut with a breaker bar and extension

[nicklk]

This is my baller drawing with MS paint of what I've done in the past

Just an idea

http://img.photobucket.com/albums/v154/nicklk/untitled-2.jpg

[dan3490]

sweet drawing man thanks lol ill give it a try tomorrow and let you know how it goes onces again thanks

[urhomieblaze]

good idea with the breaker bar,
as a last resort.. jam an old scewdriver in the rotor and try. done it in the junkyard afew times. also a length of cheater pipe on the breaker bar helps

[dan3490]

thanks most likely need new rotors rusted aways -__-

[mrsatisfiher]

stick a screw driver in the middle of the caliper right to the disk and use a long poll attach to the wrench or just take a hammer and keep on pounding the wrench and hopefully u break it loose

[M@]

Let the fucker soak for a day in PB Blaster, too.

[Nick_S]

Let the fucker soak for a day in PB Blaster, too.
:werd: That shit is the bomb!

[dan3490]

yea i tryed some pb blaster on my homies teg. thats the 1 we used a 12' bar with 2 people standing on it to break it but ill give it a try thanks every one.....ey any 1 got a way to get the rotor screw out . . . its striped and rusted so i aint even gonna try with a screw driver or drill maybe drill the bitch out and leave it with out the screw

[M@]

12 FOOT bar? Interesting. Take pics next time you do that.

[jackmode9316]

The bar I use as a "cheater" on the breaker bar is a good 6 or 7 feet long and its hard to use that in my garage. I couldn't imagine using one twice as long. My cheater was made cakework of cracking the Preludes axle nut and also for the crankshaft bolt on the REX.

[1.8fury]

cut-off wheel FTW.

[dan3490]

lol the 12'er was in a carport ;) + it was the only bar around lmfao..........and cut the wheel off huh wish i had the jaws of life lol jk

[Martian]

not cut the wheel off, a cut off wheel. John is telling you to just cut the axel nut off. As for the rotor screw drill it out if its stripped.

[dan3490]

lmfao i know dont cut the wheel off. just a feeling its pissin me off.lol

[Mario]

I'd just shoot it with a shotgun. *shrugs*

[vince]

I'd just shoot it with a shotgun. *shrugs*

HAHAHA beat me to it.

[aznboiek9]

does that really work?

[jackmode9316]

does that really work?
What shooting it with a shotty? yeah it works if you don't mind peppering your legs with buckshot!
There is an article on here about an 80 yr old man who could'nt remove the AXLE nutt. So he shot it with a 12 Guage...Not a smart move.