Notes for my install

[-=[Juztin]=-]

Hey Tobi, your PM box is teh full.

I'll however just create a thread and post up some tidbits that may be helpful to you regarding this install. Just had a good thread come up recently on the Z board covering the install of the Greddy kit.

http://my350z.com/forum/showthread.php?t=211378

There's actually some good information, especially in the 2nd page of it that covers bending the PS lines around the passenger side turbo as people who have not done this previously had their PS line get melted thru and a lot of no fun after that.

Here's a quote from Phunk regarding that:

"One thing, make sure that you bend the power steering (http://my350z.com/forum/showthread.php?t=211378&page=2#) line by the passenger side turbo (http://my350z.com/forum/showthread.php?t=211378&page=2#) out of the way. Its a common problem to have it rub on the turbo until it wears thru and leaks. What I always do is bend it away as much as I can, which isnt much, and then I take a peace of that blue pushfit fuel line and cut a slit down it to open it up, slide it on around the pipe, and safty wire it on. That way if the engine moves enough to touch it, its padded and will not wear thru for years if ever)."

Also one of the pics in the 1st thread mentions Scott's product, that's the Wastegate relocations I ordered from him and shows you a pretty good angle of where to expected the wastegates to be.

[-=[Juztin]=-]

Here's another thread referencing a possible heat issue burning thru a coupler:

http://www.my350z.com/forum/showthread.php?t=156709

[-=[Juztin]=-]

A few recommendations I dug up from my notes..

you're going to want to tell the mechanic move the power steering non-pressurized line on the passenger side away from any heat sources...and make sure they re-install the air-bag sensor in a verticle alignment.


And as Kenny said take care of the PS line and the air bag sensor.

Also put the rubber couplings on the turbos before you put them on the car or it will be a pain putting them on with the turbos in place.

Make sure you have the oil line fitting on the turbo pointing in the right direction as they cannot be adjusted with the turbo in place if they are wrong.

wrap w/ heat wrap and also fabricate a bracket to hold it back an additoinal inch from where it currently sits. This should give around 2" of clearance from driver side turbo manifold which will burn a hole right thru it otherwise.

[Kwando]

so i guess this means your compression numbers are good and tobi has the thumbs up to do the install?

[-=[Juztin]=-]

so i guess this means your compression numbers are good and tobi has the thumbs up to do the install?Yep! Engine looked great, suprised for how much hell I gave it over the last 88k miles :rofl:

[Kwando]

sweet dude... i finally found the problem with my a/f readings... the #1 O2 Lambda input was at fault... hooked it up to #2 and it works fine...


that installl looks like a lot of fucking work!!! i'm sure tobi will have fun with your install...

[-=[Juztin]=-]

sweet dude... i finally found the problem with my a/f readings... the #1 O2 Lambda input was at fault... hooked it up to #2 and it works fine...


that installl looks like a lot of fucking work!!! i'm sure tobi will have fun with your install... Awsome to hear bud, when you tuning again? I'll swing by :cool:

[velocity]

grats justin. guess im next on the get boost installed list.

[-=[Juztin]=-]

grats justin. guess im next on the get boost installed list.thanks bud, it's been a long time in waiting for sure... GetRDUN!

[Kwando]

=-;597739']Awsome to hear bud, when you tuning again? I'll swing by :cool:

i had an appt tomorrow with tobi, but i cancelled because i didn't think we were going to find the problem... late tonight we found the issue, so i hope they can still fit me in...


and RETURN YOUR CALLS!!!

[ryanman]

Awesome!!

[STIBungy]

I bet you're looking forward to pulling on me. :D

=-;597733']Yep! Engine looked great, suprised for how much hell I gave it over the last 88k miles :rofl:

[-=[Juztin]=-]

I bet you're looking forward to pulling on me. :DLOL, I know what your up to buddy, more George vs. Harold stories to come :cool:

[Martian]

can't wait to see how fast the finished deal is.

[chris_venturini]

the great twin turbo install of 06

[-=[Juztin]=-]

the great twin turbo install of 06 Minus the horror stories! :rofl:

[Kwando]

justin im sure you will be done and driving around within no time

[-=[Juztin]=-]

justin im sure you will be done and driving around within no timespeaking of which bud, how u liken the tune?

[Weston]

the great twin turbo install of 06

If Tobi is busy, we can always have an install-fest. Just picture the 240 disaster on a larger scale. Nissan + even tighter engine bay + two turbos + easily distracted, non-motivated HAI idiots = estimated completion time in mid 2007. :D

[-=[Juztin]=-]

Tobi -

The complete list of missing pieces are as follows (you can reference the Greddy TT Intercool Installation Manual parts list to get a visual reference)

Missing Items:

Item #9 "Silcone Hose 70mm straight coupler"
Item #10 "Silicone Hose 60mm to 50mm reducer coupler"
Item #16 "Straight tube 10mm radius"
Item #20 "Washer tank relocation bracket set (small bracket was missing)"
Item #21 "Washer tank extension hose 5mm radius, 1500mm length"

EDIT: Tobi - I sent you the intercooler install guide to your tcperf.com email account.

[Kwando]

=-;598312']speaking of which bud, how u liken the tune?

love it... did some logging tonight and it appears to be running more richer than when it was on the dyno (fine with me, better rich than lean)... and showing no knock at all...

[-=[Juztin]=-]

http://www.my350z.com/forum/showthread.php?t=203359&highlight=oil+catch+can+placement

oil catch can placement

[-=[Juztin]=-]

http://www.forgedperformance.com/store/images/thumb/t_16147_01.jpg

bov location example

http://www.forgedinternals.com/store/product.php?productid=16147&cat=259&page=1

[Steve_C]

the great twin turbo install of 06Hopefully it won't overshadow Ashton's Great Twin Turbo Install of 04

[HONDA GHANDI]

You want progress pics posted in this thread Juztin or would you prefer me to send those to you privately like usual? ;)

[-=[Juztin]=-]

Here's fine Tobi :cool:

[Nightfall]

Post them! Post them!

[chris_venturini]

we need to have a run when your done!

[-=[Juztin]=-]

we need to have a run when your done!Sure, up your boost ;)

[Kwando]

POB tobi!

[-=[Juztin]=-]

some possible interesting software for the UTEC Tobi in regards to tuning:

http://www.my350z.com/forum/showthread.php?t=189328

[ryanman]

the great twin turbo install of 06

Oh god, I hope this one is twice as bad as yours, I need some good comedy!!!

[ryanman]

Hopefully it won't overshadow Ashton's Great Twin Turbo Install of 04

LMAO!!!!!

[-=[Juztin]=-]

Tobi - the wastegate relocation kit should be shipped to your door in the next 2-3 days. Just an FYI :cool:

[HONDA GHANDI]

sweet. I didnt get too much done today, I have to thank Nismo for the superior design of their headers. Getting the bolts out of them has been fun. In retrospect I should have just pulled the entire engine to pull the headers. It would have taken less time.

[Dave_L]

Didn't people say it was easier to pull the motor to boost the Z?

[ryanman]

I read that somewhere a time or two.

[-=[Juztin]=-]

I feel your pain LOL, it was a BIATCH to get the nismo headers on originally. Just double-checked with Scott (the guy that makes the relocation kit, he just reconfirmed it'll ship out shortly, looks like his welder will get the kit done tomorrow and ship out priority UPS).

[MrsGhandi]

Bloody knuckle count for Tuesday is 3! OMG!

Here is an update and some pics. Nothing too rediculous today. Just some light duty stuff.
Pan and spacer ready to be installed.
http://www.dynojunkies.com/forum/album_pic,pic_id,36.html
Right side of pan with spacer will need to be bent to clear subframe for turbo drain.
http://www.dynojunkies.com/forum/album_pic,pic_id,35.html
Left side of pan also.
http://www.dynojunkies.com/forum/album_pic,pic_id,34.html
Heat wrapped fuel lines.
http://www.dynojunkies.com/forum/album_pic,pic_id,33.html
Clutch and both manifolds installed.
http://www.dynojunkies.com/forum/album_pic,pic_id,32.html
Right side...
http://www.dynojunkies.com/forum/album_pic,pic_id,31.html
Left side...
http://www.dynojunkies.com/forum/album_pic,pic_id,30.html

[velocity]

sahweet

[Kwando]

getting close justin! you excited?

[ryanman]

nice

[-=[Juztin]=-]

ooooooh very nice Tobi & Barb. Kinda weird to see the car finally getting TT'd after waiting so long heheh. Simon - I can't wait! :eek::eek::eek::biggrin::biggrin::biggrin:

Tobi - do you need the Intercooler install manual? I can email it to you if you need, can't remember if I already did that. Also did you ever get around to downloading the service manual? Lastly, there is a new version for the UTEC, v2.7 - just an FYI. Definately looking very good heheh

[HONDA GHANDI]

I got everything I need so far Justin. I will download that 2.7 when Im ready to start it up. Thanks.

[Weston-work]

What's the oil pan spacer for?

[doogie06]

To space the oil pan.

[-=[Juztin]=-]

What's the oil pan spacer for?
+10hp

[ryanman]

To space the oil pan.

:werd:

[Dave_L]

It's like getting a bigger oil pan.

[Weston-work]

It's like getting a bigger oil pan.

That's what I figured, but does it come with a longer oil pickup tube? If not, it seems pretty much pointless.

[myshtern]

Maybe one of the turbos hangs too low so you need to extend the oil pan

[HONDA GHANDI]

There is a spacer for the oil pickup also Weston.

[Chris_V=|work|=]

i think im going to cry when justin beats me... then ill build an engine :)

[ryanman]

then ill build an engine :)

I will DEFINATELY subscribe to that thread when it happens, LOL!!

[Chris_V=|work|=]

hey! the turbo install was not my fault! ... it was the faulty injector seals (which happened twice) and the inversed safc...

[HONDA GHANDI]

Today's update:
1 bloodied knuckle (now all but 2 are fucked up)
1 puncture wound
1 lump on my skull
2 new special tools made
2 turbos mounted


Got the turbos in, mounted and plumbed for oil today, got the clutch finished and tranny back in. Here are the pics. Greddy has a shitty install manual so I am basically winging it at this point. I had to make some tools to get to the bolts mounting the turbos to the manifolds. They are a tight fit. I have come up with a few things that will keep it reliable like securing the oil lines to the block to keep them from rubbing through anything.
http://www.dynojunkies.com/forum/album_pic,pic_id,37.html

Left side turbo mounted, charge pipe adapter installed.
http://www.dynojunkies.com/forum/album_pic,pic_id,38.html

Right side turbo mounted, PS line relocated and covered for protection.
http://www.dynojunkies.com/forum/album_pic,pic_id,39.html

Now the money shot of the day...
http://www.dynojunkies.com/forum/album_pic,pic_id,40.html

[HONDA GHANDI]

Tomorrow I hope to get the wastegates done, the exhaust hung and rest of the tranny stuff back together. Start on the intercooler piping and injectors, and fuel pump.

[velocity]

very sexy tobi nice work. soon you can have the joy of work on my simple d16 lol

[HONDA GHANDI]

I wont bleed nearly as much at least. This thing has sharp corners everywhere and no space to work with. Added to that is that I have been using safety wire on all the harnesses and fuel lines and that shit is like tiny shark teeth. :D

[Weston-mobile]

Damn you, Justin... we cant ricer fly-by you anymore. Well, at least Chris' engine build will be hillarious...

[Martian]

Nice work as usual Tobi

[Kwando]

sweet work tobi... can't wait to see the finished product...

[Dave_L]

Lookin sweet!

[-=[Juztin]=-]

awsome update, definately the money shot their with the turbo's mounted, gosh dyam that fit looks tighter than a virgin! :cool:

[-=[Juztin]=-]

definately great touches on the oil lines and ensuring they wont rub against some uber hot stuff etc. Keep up the excellent work - if you feel you need to change any hosing or something for heavier duty just do it :cool:

[ryanman]

Juztin has alot of ricer fly-bys to make up for.

[MrsGhandi]

Nice sig Juztin ;)

[colocomp]

Looking forward to seeing it Justin and welcome to the Dark Side.

I would not mind watching a little of the tuning when you guys dyno it, if at all possible?

[Kwando]

justin, I hope that you don't run into problems with bolts backing out on the manifold/wastegate? it would suck to get to those manifold bolts... i know alot of the s2k guys have problems with bolts backing out...

[-=[Juztin]=-]

Thanks Colocomp - Tobi will probably post on here the date when it's getting tuned, but I can say it'll probably be during the week, in which case very few people will probably be able to make it. Heck I know I wouldn't probably show until around 5pm cause of work :( But I'll let you know none-the-less :cool:

Simon - I've never heard any reports whatsoever of bolts backing out in FI'd Z's in general but I have a little preempitive fix in the works. Just a little update, all the major turbo parts have been installed, FMIC mounted, almost all filter piping & charge piping has been run. Just on to the numerous little things like installing BOV, fuel pump, turbo timer, plugs, injectors etc.

Also I ended up having to switch back to stock exhaust since the Borla exhaust was cracked AGAIN! ARGH! The borla exhaust has been nothing but trouble for both myself and Tobi. It was also ghetto fixed to prevent it from leaking. But since it cracked again, I decided to go back to stock exhaust for the long run as the metal quality in the stock exhaust is 10x's better. Also, the stock exhaust has flex sections in the Y pipe so that should also greatly reduce any vibrations in the exhaust piping/downpipe etc so should also protect against any bolt's backing out issues if they were a possibility.

It'll probably hurt the spool a slight bit cause the Y pipe has a small cat in it, pluls it's 2.5" piping, and it'll be really quite exhaust note. But still not going to be a sleeper with the wastegate dumps dumping directly to the ground :) Should scare both small children and moms alike. The wastegate relocation kit looks damn slick under the car with the dumptubes looking like they mean all business ;)

[velocity]

sounds good justin. i'm droppin my car off at tobi's monday afternoon the 25th.:Beer:

[-=[Juztin]=-]

sounds good justin. i'm droppin my car off at tobi's monday afternoon the 25th.:Beer:

Congrats Chris!! Come join the dark side :D Keep us updated when you do that :cool:

[Kwando]

justin have tobi fab up an exhaust for you... 3" catless back...


also let me know when you need a ride to get the car...

[Nightfall]

Justin:

Are the internals stock? What numbers are you shooting for?

Nice work Tobi! :D

[TXKompressor]

Thats beautiful J dawg... Looks sexy as hell

Congrats

[-=[Juztin]=-]

Thanks Rob :cool:

Nightfall - stock internals, as for numbers I'll be happy w/ whatever the twins can put out at 7.5psi I'm sure :D lol. Probably be in the area around 350hp or so is my guess.

[Kwando]

i say 400

[Martian]

That crack in the exhaust sucked. I was suprised when Tobi found it. It was way to rigid a system, and the piping was thin as hell.

Overall though, it looks badass and should scream once its tuned.

[MrsGhandi]

Update for Sept 18, 2006 from Honda Ghandi

I finished most of the stuff under the hood today, I am missing a couple of couplers though. (Thanks again Greddy) The coolant overflow bottle fit terribly in the position that they would have you install it so I made my own install bracket and put it on the right side of the fan shroud. I also installed the catch can today. Tomorrow the intercooler couplers will arrive and I can finish the under hood stuff and move into the interior and electrics.
http://www.dynojunkies.com/forum/album_pic,pic_id,41.html
http://www.dynojunkies.com/forum/album_pic,pic_id,42.html
Here is a pic of the modified fuel rail before its install
http://www.dynojunkies.com/forum/album_pic,pic_id,43.html

And another after the install...
http://www.dynojunkies.com/forum/album_pic,pic_id,44.html
Here is an overall shot of what is left to do.
http://www.dynojunkies.com/forum/album_pic,pic_id,45.html
A better shot of the washer bottle install, the Greddy instructions sort of suck so this may helps someone out.
http://www.dynojunkies.com/forum/album_pic,pic_id,46.html

[velocity]

looks great tobi. thats a big ass intercooler

[ryanman]

Nice.

[Kwando]

looks great as always tobi... keep up the awesome work

[HONDA GHANDI]

Tommorow:
Turbo timer
Coupler install and finish front bumper and fender liners
MAP sensor
CAS wiring
hopefully startup and leak check.

[-=[Juztin]=-]

SWEET ASS SWEET!!:cool: :cool:

[Nightfall]

Biggest FMIC evar... nice!

[exciv2000]

Lookin' great! Love to take a quick ride in it sometime.

[Pang]

Nice, looking good!

[kwando_MDA]

no updates today justin or tobi??

[J.Dub]

yeah really!!!

[Martian]

no updates today justin or tobi??
Tobi went mental from the sheer stress of J units car. He was admitted to the Luthern psychiatric ward at 6:30pm. Barb is inconsolable, Mike got a tattoo to commemorate Tobi in his prior greatness, and hell froze over.





























Thats one scenario anyhow!

[Kwando]

Tobi went mental from the sheer stress of J units car. He was admitted to the Luthern psychiatric ward at 6:30pm. Barb is inconsolable, Mike got a tattoo to commemorate Tobi in his prior greatness, and hell froze over.





























Thats one scenario anyhow!

bwahaha!

[velocity]

Tobi went mental from the sheer stress of J units car. He was admitted to the Luthern psychiatric ward at 6:30pm. Barb is inconsolable, Mike got a tattoo to commemorate Tobi in his prior greatness, and hell froze over.





























Thats one scenario anyhow!
that explains why mike answered the phone when i called not barb...

[HONDA GHANDI]

Barb was in a conference downtown all day yesterday, Mike and I had to keep on top of the phones so I didnt get a chance to post an update or pics.
The car is near completion, Today I have to start the task of writing a basemap from scratch and try to get it on the dyno and start the tuning process. If all goes well it should be done tomorrow.

[MrsGhandi]

Josh...you crack me up

[-=[Juztin]=-]

http://img101.imageshack.us/img101/8219/img025xg8.jpg

Camera phone pic FTW!

[Steve_C]

Looking good Justin! can't wait to co-pilot!

[Dave_L]

Pure sex!

[HONDA GHANDI]

dyno dyno dyno....

[velocity]

i want a ride!

[-=[Juztin]=-]

Thanks guys, but please direct all your compliments to Tobi and his exceptional work as always. :cool:

As for rides, u guys know where to find me :D

[Dave_L]

So is it done?

[Kwando]

So is it done?

basically... i'm taking him to get it tomorrow hopefully

[Dave_L]

Freakin' sweet!

[velocity]

what time you taking him simona? i might swing by since i'm up that way.

[Kwando]

we plan on leaving at 4... i might try to sneak out early

[velocity]

sweet maybe i'll just meet u guys up there.

[-=[Juztin]=-]

It still needs a lot of tuning and some misc work like replacing the catch can lines and possibly drilling a hole in the throttle plate to smooth out the idle and stop high rpm sudden pedal let off stalling. Wont know for sure if it's going to be done tomorrow until the evening, but Chris just shoot me a call around 3pm or so.

[velocity]

sounds good pm me your # i think i lost it

[Steve_C]

what time you guys gonna be at tobi's? Maybe i will stop by and we can grab some happy hour food or something

[-=[Juztin]=-]

I'm not going to make any plans until tomorrow and until I know if the car's a GO or not. I definately dont want to rush Tobi with tuning. I'm also going to leave him alone to tune the UTEC without distractions so let's meet up somewhere after I pick up the car please if tomorrow is a go :)

I'll call you steve tomorrow when i know more and we can hopefully make some plans then.

Chris, PM me your #

[ryanman]

You still have the other wheels?

[forum]

You still have the other wheels?

Last I heard he was sleeping with them or something like that

[HONDA GHANDI]

justin, the car is GO! I stayed late last night to work out some bugs and came in early this morning and got it finalized. Im going to take a few more pics right now of the rest of the install and take a dyno video. (I have never tried a video with this camera, hope it comes out) I will post up the remainder of the notes and pics here in a bit as well as a dyno chart. The numbers aren't as good as we had hoped for but I think you will be pleased.

[velocity]

yay pics and video can't wait

[Dave_L]

Cant wait for the pics/dyno!

[-=[Juztin]=-]

sweet! As long as it's got more than 220hp i'll be happy :rofl:

[MrsGhandi]

Final update.

Yesterday we finished all the little odds and ends and got the car on the dyno for the first time. After about 6 hours on the dyno doing load range tuning and rpm /load tuning we came up with some pretty impressive numbers. Here are the rest of the pics.
Starting with my left hand after "knuckling" down and finishing this car ahead of schedule. ;)
http://www.dynojunkies.com/forum/album_pic,pic_id,47.html
Car on the dyno
http://www.dynojunkies.com/forum/album_pic,pic_id,49.html
catch can installed
http://www.dynojunkies.com/forum/album_pic,pic_id,51.html
Pic of the intake pipe and the charge pipe
http://www.dynojunkies.com/forum/album_pic,pic_id,50.html
The finished checklist
http://www.dynojunkies.com/forum/album_pic,pic_id,52.html
FMIC all installed and ready to rock.
http://www.dynojunkies.com/forum/album_pic,pic_id,53.html
Turbo timer pics
http://www.dynojunkies.com/forum/album_pic,pic_id,54.html
http://www.dynojunkies.com/forum/album_pic,pic_id,55.html

And finally... the chart. This is on the stock 7 psi spring that comes with the kit.
MAP readings were at 6.6psi. Enjoy.
http://www.dynojunkies.com/forum/album_pic,pic_id,56.html

[-=[Juztin]=-]

NICE! :D :D :D

[kwando_MDA]

sweet numbers!

like I said 400rwhp

[Steve_C]

Sweet! I can't wait to co-pilot :)

[-=[Juztin]=-]

:rockon::rockon::rockon::rockon::rockon::rockon::r ockon::rockon::rockon::rockon::rockon:OMG This day is going to go by so DAMN SLOW! Awsome work Tobi!!!

[Dave_L]

Awesome! I'd love to get a ride also when the opportunity arises. :)

[Conrad]

tick tock tick tock tick tock

[MrsGhandi]

http://video.google.com/videoplay?docid=3198408310474115670


video here. SOrry for the quality, its just my still camera.

[Dave_L]

:drool:

[TXKompressor]

SO fucking sweet!... Damn J... I want a ride...

[doogie06]

Nice numbers, good work tobi.

[-=[Juztin]=-]

SO fucking sweet!... Damn J... I want a ride...Bud... This can now be used as an excuse for you to come visit us!

[M@]

Good work Tobi. Damn, I want a 350 now... lol.

[TXKompressor]

Hahahaha no shit... Nice numbers man

I just may have to do that... Probably not till after the new year though... got San Diego for Tday and bunch of family coming for XMAS....


=-;608620']Bud... This can now be used as an excuse for you to come visit us!

[mirror]

sweet #'s.
Looks like another great install by Tobi.

[HONDA GHANDI]

We will have to get you a badge made up for the trunk lid. 399 Z

[Weston-work]

So, when do I get to drive it? :D

Damnit, I want one now... :cry: What was the total cost to turbo it?

[velocity]

awesome! thought i was gonna have to cancel my appointment for monday but i got my gremlins all figured out.

[MrsGhandi]

No gremlins!!!!! We'll see you Monday ;)

[Weston-work]

Yeah, damn those gremlins...

http://i36.photobucket.com/albums/e36/dorito31561/Gremlin.jpg

[chris_venturini]

damn.... nice... i now realize that there is no point in me giving carlos a call.

[Kwando]

car is fast!

[-=[Juztin]=-]

The car is rediculous! Boost is so much fun and man those wastegates are teh LOUD! I already scared a few people giving them ricer boost dumps!

I had an STi initially get behind me after the driver looked like he noticed my IC. He paced me for a while, I then proceeded to give him a demo that the IC is not merely show, and he immediately then fell back and turned off the highway, so no George vs. X stories yet :(

[chris_venturini]

i saw a blue 350 a couple days ago with a front mount and a rediculous amount of greddy stickers all over it.

[Weston]

Justin is going to be such a street ricer now... :rofl:

[Dave_L]

Justin...I NEED A RIDE!

[velocity]

=-;609007']The car is rediculous! Boost is so much fun and man those wastegates are teh LOUD! I already scared a few people giving them ricer boost dumps!

I had an STi initially get behind me after the driver looked like he noticed my IC. He paced me for a while, I then proceeded to give him a demo that the IC is not merely show, and he immediately then fell back and turned off the highway, so no George vs. X stories yet :(

lol that shit was fun. i had a smile on my face for like the next hour. all i can say is "wow" 400 hp is fun! thanks for the ride justin! btw usps sucks! mine & simons spark plugs are MIA!

[Weston]

btw usps sucks! mine & simons spark plugs are MIA!

I usually like USPS, but their lack of tracking sucks. At work, we switched to them to save a few bucks on sending out maintenance tapes, but now we have pissed off customers because they don't get their shit. On the other hand, today I came home to find that UPS had delivered a package for another address... that's the third damn one this week!

[Steve_C]

Thanks Justin for letting me ride along, car is fun!

Props to Tobi for a good and clean install!

[mirror]

you should stop by echostar tomorrow during lunch Justin, I want to see.:)

[Kwando]

you should stop by echostar tomorrow during lunch Justin, I want to see.:)

he's not driving it anymore.... its already packed away for the winter...

[-=[Juztin]=-]

Hey speak for yourself Simon, I've already got like 10x more miles than you from when you got your car back and that's just on one day alone! lol A turbo'd Z is just wayyyyyy to much fun! :D Jon, definately I'll try and stop by Echostar tomorrow I'm gonna take the Z to work cause a coworker wants a ride :cool:

[mirror]

sweet give me a call when you stop by.

[Conrad]

Justin...I NEED A RIDE!

:werd:

[HONDA GHANDI]

You should sell tickets J-Unit.

[MrsGhandi]

Juztin's the new HAI bicycle....everyone wants a ride.

[Weston]

I'll refrain from making fun of him until after I get a ride... ;)

[-=[Juztin]=-]

LOL great idea Tobi :D Come on Barb, at least I'm a better piece of *ss than the original HAI Bicycle!

We should plan to do a meet tonight so I can get all these ride alongs taken car of :D Hopefully it won't be raining.

[HONDA GHANDI]

Jackass II tonight.

[-=[Juztin]=-]

Jackass II tonight.
Werd that sounds like a good idea :cool:

[Dave_L]

I'm going with my brother to get some beerz for his birthday tonight.

[Conrad]

I'm going with my brother to get some beerz for his birthday tonight.

fuck that...

[M@]

Jackass II tonight.
Bastards. http://www.highaltitudeimports.com/t45908-jackass-2-movie-meet.html